Lanode.com

  • Increase font size
  • Default font size
  • Decrease font size
Home Industrial PoE Switches & Converters Unmanaged Switches 4 Port GbE Switch with 1 or 2 Fibre and 4 Port PoE+

4-Port Gigabit Ethernet Switch with 1 or 2 Fibre and 4-Port PoE+

E-mail Print

4-Port Gigabit Ethernet Switch with 1 or 2 Fibre and 4-Port PoE+

4-Port 10/100/1000Base-T(X) with 1 or 2 Fibre and 4-Port PoE+ Gigabit Ethernet Switch

Our industrial High Power PoE switches are specifically designed to meet IEEE 802.3af/at standards for powering network devices with up to 30 watts output per PoE port. With PoE function, it becomes easier to install network devices such as IP surveillance cameras, wireless access points, IP phones, and other PoE enabled devices in outdoor or remote areas where there are hard-to-reach power source. The IGS-402F-4PH(E)24, 5-port and 6-port unmanaged full-Gigabit Ethernet switches, support 4-port Power-over-Ethernet on ports 1 to 4 and 1-port or 2-port 1000Base-X optical fibre. The switches are classified as power source equipment (PSE) and can be used to power IEEE 802.3af/at standard devices (PD), eliminating the need for additional power cable wiring. Moreover, its built-in power input booster of 24 VDC and 48VDC for PoE/PoE+ output without external power converters or power supplies, it is able to fit all the common 24/48 VDC power systems found in industrial fields or cabinets. These PoE switches support IEEE 802.3/802.3u/802.3x/802.3ab with 10/100/1000M, full/half-duplex, MDI/MDI-X auto-sensing to provide an economical highbandwidth solution for your industrial Ethernet network. Wide operating temperature (-40 ~ 75°C), E models, especially for industrial harsh environment applications.

4-Port 10/100/1000Base-T(X) with 1 or 2 Fibre and 4-Port PoE+ Gigabit Ethernet Switch schematic

Features:

  • Provides 4-port IEEE802.3at/af PoE Output (30W)
  • 24/48VDC Redundant dual input Power Design
  • 4-Port 1000Base-T RJ-45 with 1 or 2 Fibre Gigabit Ethernet
  • Wide Operating Temperature -40 ~ 75°C (IGS-401F-4PHE24, IGS-402F-4PHE24)
  • UL508,CE,FCC, certification
  • Industrial grade EMS certification
  • IP30 rugged metal housing

Specifications:

IEEE Standards:

  • IEEE 802.3 10Base-T Ethernet
  • IEEE 802.3u 100Base-TX Fast Ethernet
  • IEEE 802.3ab 1000Base-T Gigabit Ethernet
  • IEEE 802.3z 1000Base-X Gigabit Ethernet
  • IEEE 802.3x Flow Control and Back Pressure
  • IEEE 802.3at, IEEE802.3af

Switch Architecture:

  • Back-plane (Switching Fabric): 12Gbps ( IGS-402F-4PH24, IGS-402F-4PHE24)

Data Processing: Store and Forward
Flow Control: IEEE 802.3x flow control, back pressure flow control
Provides broadcast storm protection: Present, Enable / Disable set by DIP sw
Jumbo Frame: 10K Bytes
MAC address Table Size: 8K
Packet Buffer Size: 1Mbits

PoE Standard: IEEE 802.3at/af
PoE RJ-45 pin assignment:

  • RJ-45 port # 1~# 4 support IEEE 802.3at/af End-Span,
  • Alternative A mode
  • Positive (VCC+): RJ-45 pin 1, 2.
  • Negative (VCC-): RJ-45 pin 3, 6.
  • Data (1, 2, 3, 6, 4, 5, 7, 8 )

Network Connector:

  • 4 x RJ-45
  • 10/100/1000Base-T(X) auto negotiation speed, Auto MDI/MDI-X function, Full/Half duplex
  • 1 or 2x 1000Base-X Fibre connector :SC Multi-mode or Single-mode

Network Cable:

  • UTP/STP above Cat. 5e cable
  • EIA/TIA-568 100-ohm (100m)
  • Fibre Cable (Multi-mode): 50/125um, 62.5/125um
  • Fibre Cable (Single-mode): 9/125um

Protocol: CSMA/CD
LED:

  • Per unit: Power 1 (Green), Power 2 (Green), Fault (Amber)
  • RJ-45 port : Link/Active (Green), Speed 10 (OFF ), 100 (Green), 1000 (Yellow)
  • Fibre Per port: Link/Active (Green)
  • PoE Port LED :
    Active : ON
    Inactive : OFF
    Fault : Flash
    (Over Load, Short Circuit, Port failed at Startup)

DIP SW:

  • DIP 1 On : Disable power failure alarm; Off : Enable power failure alarm
  • DIP 2 On : Disables broadcast storm protection; Off : Enable broadcast storm protection

Reserve polarity protection: Present
Overload current protection: Present
Power Supply: Redundant Dual DC 12/24/48V (9.6~60VDC) Input power (Removable Terminal Block)

Alarm Relay Contact: Relay outputs with current carrying capacity of 1 A @24VDC
Removable Terminal Block: Provide 2 Redundant power, Alarm relay contact, 6 Pin
Operating Temperature: 0 ~ 60°C; -40 ~75°C
Operating Humidity: 5% to 95% (Non-condensing)
Storage Temperature: -40 ~ 85°C
Housing: Rugged Metal, IP30 Protection
Case Dimension: 38 X 106 X 142mm (W X D X H)
Installation mounting: DIN Rail mounting and Wall Mounting
EMC/EMS: CE, FCC
EMI: FCC Part 15 Subpart B Class A, CE EN 55022 Class A
EMS:

  • EN61000-4-2 (ESD) Level 3,Criteria B
  • EN61000-4-3 (RS) Level 3,Criteria A
  • EN61000-4-4 (EFT) Level 3,Criteria A
  • EN61000-4-5 (Surge) Level 3,Criteria B
  • EN61000-4-6 (CS) Level 3,Criteria A
  • EN61000-4-8 (Magnetic Field) Level 3, Criteria A

Safety: UL508 (Pending)
Rail Traffic: EN 50121-4
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Warranty: 5 years

 

How can we help?

Search

Live Demo of FRM220 Chassis

Related Products